A good DIY chicken feeder is a capped length of PVC pipe, a bucket with side ports, or a treadle box that stays shut until a hen steps on it. Each one costs about $10 to $80 and takes an afternoon. The rest of this page gives cut lengths, materials and the mistakes that waste feed.

Feed is the biggest running cost of a flock, and a lot of it ends up on the ground. A feeder that keeps feed off the floor, out of the rain and away from rodents pays for itself fast.

How much feed and feeder space you need

A laying hen typically eats about 1/4 pound of complete feed a day, roughly 110 to 120 grams. That is an approximate figure. Bantams eat less, big dual-purpose breeds eat more, and every hen eats more in a cold snap.

FlockFeed per day (approx.)Per week (approx.)
4 hens1 lb7 lb
6 hens1.5 lb10 to 11 lb
10 hens2.5 lb17 to 18 lb
12 hens3 lb21 lb

Size the feeder to hold three to seven days of feed. A feeder that holds a month encourages stale feed and mice. One that holds a day means a daily chore.

For space, allow about 4 inches of trough or port width per hen. A gravity feeder with a single 4-inch port suits about four hens, and a flock of ten wants two feeders in different spots so a bossy hen cannot guard all of it. If you are still deciding flock size, the plans for 6 chickens and plans for 10 chickens pages show what fits.

Where to put the feeder

Put it under a roof, off the ground, and away from the waterer. Water splashed into feed makes a damp paste that goes bad quickly. A walk-in coop like the 8x8 walk-in shed coop gives you dry floor space for it, and the coop interior layout guide shows where feeders and waterers usually sit relative to roosts and nest boxes.

Hang or stand the feeder so the lip is about the height of a hen’s back. Lower than that and they scratch feed out and stand in it. Higher and young birds cannot reach.

Build 1: PVC gravity feeder

This is the standard wall-mounted tube feeder. It holds a lot of feed and drops it into the port as hens eat.

Materials (about $15 to $25):

  • 1 piece of 4-inch Schedule 40 PVC pipe, 36 inches long (3-inch also works and holds less)
  • 1 four-inch 90-degree elbow
  • 1 four-inch cleanout adapter with threaded plug, or a slip cap
  • 2 or 3 pipe straps (galvanized or stainless) sized for 4-inch pipe
  • 4 exterior screws, #8 by 1-1/2 inch
  • PVC primer and cement (or leave the cap unglued so it comes off)

Cut and assemble:

  1. Cut the pipe to 36 inches with a hand saw or miter saw. Deburr the cut edge with sandpaper so it does not scratch beaks.
  2. Dry-fit the elbow onto the bottom of the pipe so the open mouth points out and slightly up, away from the wall.
  3. Glue the elbow with primer and cement, or leave it dry-fit if you want to take it apart to clean. Cement is permanent.
  4. Fit the cleanout adapter or cap on top. This is your fill lid, so do not glue it.
  5. Screw the pipe straps to the wall studs or a backer board. Keep the elbow mouth about 6 to 8 inches off the floor for standard-size hens, or hang the whole thing from a chain a little higher.

A 36-inch run of 4-inch pipe holds about 2 gallons, which is roughly 9 to 10 pounds of pellets. Feed density varies, so fill it once and see. Six hens eating about 1.5 pounds a day will empty it in a bit over a week if it is full.

Pellets and crumbles flow well. Whole grains and scratch can bridge in the pipe and stop flowing, so use this one for complete feed.

Build 2: PVC elbow port feeder (the low-waste version)

Hens waste most feed by billing it out of an open trough. A port feeder limits that because the feed sits inside a curve, and the hen has to reach in to get it.

Materials (about $20 to $30):

  • 3-inch Schedule 40 PVC pipe, 24 inches (holds about 4 pounds, which suits 3 to 4 hens)
  • Two 3-inch 90-degree elbows, or one wye plus one elbow
  • A 3-inch cap
  • A short 3-inch pipe stub, 4 inches
  • Zip ties or hose clamps, and a mounting board

Assembly:

  1. Cut the main tube to 24 inches and the stub to 4 inches.
  2. Glue one elbow to the bottom of the tube. Glue the stub into the elbow so the mouth faces the front and tilts upward at about 20 to 30 degrees. This lets feed settle inward when the hen stops eating.
  3. Fit the cap on top without glue.
  4. Mount with two straps to a board and then to the wall, with the mouth about 3 inches below a hen’s back height so she reaches slightly down into it.
  5. Round every edge with sandpaper. If your hens cannot reach comfortably, raise the mouth an inch or two.

Because the opening is only about 3 inches wide and tilted back, a hen cannot rake feed out by scratching. The trade-off is that only one or two birds can eat at a time per port. Build one port for every 3 to 4 hens, or run two on a shared mounting board.

Build 3: Five-gallon bucket feeder

The bucket feeder is the cheapest option and holds the most feed. A 5-gallon bucket holds roughly 20 pounds of pellets, about two weeks for six hens.

Materials (about $10 to $20):

  • 1 food-grade 5-gallon bucket with a snap or gamma lid
  • A 3-inch hole saw
  • Chain or rope, 2 S-hooks, and an eye bolt for hanging

Build:

  1. Mark 3 or 4 feed ports spaced evenly around the bucket. Put the bottom of each hole about 2 inches above the bottom edge so a lip of feed stays inside.
  2. Drill each hole with the 3-inch hole saw. Drill slowly. Plastic grabs the bit and can crack.
  3. Sand every cut edge until it is smooth. Sharp plastic cuts combs.
  4. Drill four small drain holes (about 1/8 inch) in the bottom. They keep condensation from pooling under the feed.
  5. Hang it from a rafter with chain so the bottom of the ports is at hen-back height, or set it on a concrete block.
  6. Keep the lid on. The lid is what keeps rain and rodents out.

Do not set the bucket on bare dirt. Feed in contact with damp ground turns moldy. A paver, brick or 2-by-4 platform works.

Build 4: Treadle feeder to keep rats out

A treadle feeder stays closed until a hen stands on the pad. Rats and mice are lighter than hens and are less likely to trigger it, and wild birds are locked out as well. It is the most work to build, and it needs a few days of hen training.

Materials (about $40 to $80):

  • Exterior plywood, 1/2 inch, one 2 by 4 foot piece
  • Two 2-by-2 boards, 8 feet each
  • 2 hinges for the lid, 2 for the pad
  • A 1-by-2 lever arm, 14 inches
  • 1/4-inch carriage bolt for the pivot
  • Exterior screws, 1-1/4 inch, and a small counterweight (a bolt or washer stack)

Cut list:

  • 2 sides, 12 by 10 inches
  • Back, 12 by 10 inches
  • Front lip, 12 by 4 inches (a hen reaches over it when the lid is up)
  • Lid, 12 by 14 inches, so it overhangs the front and sheds rain
  • Pad, 10 by 12 inches, hinged at the front edge
  • Floor, 12 by 12 inches, raised off the ground on two 2-by-2 feet

How it works:

  1. Screw the sides, back, front lip and floor into an open-top box about 12 inches wide and 12 inches deep.
  2. Hinge the lid at the back so it swings up and clears the feed.
  3. Hinge the pad to a short base in front of the box. Fasten the 14-inch lever under the pad to a pivot on a side wall.
  4. Connect the lever’s far end to the lid by a short link or chain. When the pad drops under a hen’s weight, the lever lifts the lid. When she steps off, the counterweight closes it.
  5. Adjust the counterweight until a hen opens it easily and the lid closes by itself.

Train the hens by propping the lid open with a stick for a few days, then removing the stick. Hens usually learn it in a few days to a couple of weeks. Bantams and light hens may not trigger a pad set for large birds, so set the weight for your smallest bird. This build is a good fit in a covered run or a larger enclosure like the one in the chicken run plans.

Keeping feed dry

Wet feed spoils fast and mold can make hens sick. Four rules cover most problems.

  • Keep every feeder under a roof, or hang it where rain cannot blow in.
  • Keep the lid or cap on after each fill.
  • Raise it at least a few inches off the ground.
  • Throw out anything that has clumped, smells sour or has visible mold. Do not top it up over stale feed.

Humid weather caps how much you should store. Buy feed in amounts the flock finishes in about a month or two.

Rodent control around feeders

Rats and mice are drawn to spilled feed, not only to feeders. Several habits matter more than any one feeder design:

  • Store bulk feed in a metal trash can with a locking lid. Rodents chew through plastic.
  • Pick up spilled feed, and sweep around the feeder weekly.
  • Some keepers pull the feeder at dusk and put it back in the morning. Hens do not eat in the dark anyway.
  • Cover every opening of the coop with hardware cloth, not chicken wire. The hardware cloth guide gives the gauge and the buried apron.
  • Check the base of the coop for gaps. The predator-proof coop guide covers the rest of the sealing job.

No feeder makes a coop rodent-proof by itself. Clean ground, a sealed building and tight storage do most of the work.

Mistakes that waste feed

  • Troughs set too low. Hens stand in them and foul the feed.
  • Overfilling an open dish. A shallow pan filled to the brim gets scattered.
  • Feeder next to the waterer. Water drips turn feed to mush.
  • One feeder for a bigger flock. Dominant hens block others. Add a second feeder away from the first.
  • Mixing scratch into a gravity tube. Whole grains jam. Feed scratch by hand or on the ground, in small amounts.

If you are also building the water side, see the DIY chicken waterer guide, and keep the dust bath in a separate spot using the dust bath guide.

Next steps

Pick the feeder that matches your flock and your pest pressure. A gravity tube is best for pellet feed, a bucket suits a bigger flock on a budget, and a treadle earns its extra work if rats are a real problem. To check how much floor and run space the flock needs around these, use the chicken run size calculator.

Our free preview PDFs show layout and dimensions for each coop design, and full plan sets are $4.99 on Etsy. The preview for the 8x8 walk-in shed coop is a good place to see where a feeder fits.